Diy Concrete Driveway Cost – The Real Cost Of Doing It Yourself!

Amazing! Diy Concrete Driveway Cost – The Real Cost Of Doing It Yourself!

Information about Diy Concrete Driveway Cost – The Real Cost Of Doing It Yourself!

Phil Puccio

Installing a concrete driveway costs between $6 and $8 per square foot for plain gray concrete and between $10 and $20 per square foot for a colored and stamped concrete driveway.

If you “do it yourself” you’ll save some money on labor costs. The labor cost of a concrete driveway is typically between 50% and 60% of the total cost of the installation.

the average cost of a concrete driveway

The average concrete driveway costs between $2400.00 and $4800.00 to install based on a 400 square foot to 600 square foot driveway size. This is based on a 4 inch thickness with a 2 foot mat of rebar for reinforcement.

Gravel subgrade preparation could add $1000.00 to $4000.00 to the total cost depending on how much gravel you need and whether you have to demonstrate and tow an existing driveway.

Do the work yourself You could save half of the above cost. Material costs for concrete and rebar for a 16′ x 25′ x 4″ concrete driveway range from $1000 to $1200.

how much it costs to pour a 12 foot x 40 foot concrete driveway

Design and gravel preparation
shaping and reinforcement
pouring the concrete
Finished concrete driveway

The cost breakdown for a 12 x 40 foot concrete driveway like the one above is below:

  1. Remove existing driveway and gravel preparation – Labor 600.00 – Materials $600.00
  2. Form and install rebar – Labor $750 – Materials $150
  3. Pouring and Finishing the Concrete – Labor $1500 – Concrete $1100 (5 inches thick)

Total cost of concrete driveway: $4700.00

Subtract labor costs if you do it yourself: $4700 – $2850 = $1850.00 Homemade concrete driveway cost.

NOTE: This is my labor and material cost in my area, your actual cost for both can vary widely based on your situation.

Basic tools for pouring a concrete driveway

Here’s a list of tools we’ll use to pour and finish a basic gray concrete driveway ready to be swept:

Please note that these are affiliate links and I may earn a small commission if you click through to Amazon and purchase these tools.

Can I pour my own concrete driveway?

The basic steps to pouring a new concrete driveway are:

  1. Remove or demolish the existing driveway (if necessary)
  2. Design & Permits – Check with local building codes for permits and design specifications
  3. Excavation and Gravel Preparation – Install and compact gravel for subgrade (amount of gravel needed will depend on your conditions and climate). At least 1 foot of gravel pad.
  4. Install forms based on your theme. Use 2×4 or 2×6 for straight shapes and PVC sheet for curves.
  5. Lay your rebar – Use 3/8″ or 1/2″ rebar and tie a mat 2 feet down the center across the entire driveway, then lay brick under it to hold it in the center of the concrete. Or use chicken wire.
  6. Calculate and order your concrete from the local ready-mix concrete plant. (Give them at least a week’s notice.)
  7. Pour the concrete level with the top of your formwork, screed and floats level.
  8. Finishing the concrete – wait for the concrete to set up and use an edger to round the edges, levitate the surface and then drag a fine broom over the concrete to give it its final finish/texture to rent.
  9. The next day, saw shrinkage joints in the concrete to prevent cracking.
  10. Seal the concrete to protect it.

To learn how to work with concrete and learn the basic skills needed to install your own concrete driveway, visit my Concrete Training Academy The concrete ground.

other factors that contribute to the cost of installing a driveway

  • Your Landscape – Is the area flat, gently sloping or steep? A steeply sloped concrete driveway is more difficult to prepare, pour and finish, which could increase installation costs.
  • The driveway size – A large driveway or a very long driveway would increase the final cost significantly. Concrete is a very expensive building material, costing about $150 per 65 square feet of driveway.
  • How thick your concrete is – The thickness of the driveway contributes a large percentage to the cost of a driveway. Concrete costs about $150 per yard – At 4 inches thick, it covers 80 square feet. At 5 inches thick, it covers 65 square feet. At 6 inches thick, it covers 50 square feet.
  • Driveway Design – Curved, circular, crescent shaped, or irregular angles can increase material (and labor) costs.
  • Adding Paint to the Mix – Adding 1 bag of paint per meter of concrete can add up to $80 per meter of concrete.
  • Stamping Concrete – Stamped concrete costs an average of $15 to $20 per square foot for labor and materials.

how to build and pour a concrete driveway

The Odell’s Complete Concrete video below shows you the basic steps to building and installing your own concrete driveway.

It will show you the demo and prep work, molding, casting and finishing process.


The DIY concrete driveway costs above are numbers I use when making estimates for my clients in my area.

These costs can vary significantly depending on the cost of materials and labor in your area.

Please use this cost as a guide to consider whether or not you want to try building your own concrete driveway.

Back to DIY concrete

Return to the home page

Another way to share everything

Prefer to share this page with others by linking to it?

  1. Click on the HTML link code below.
  2. Copy and paste it with your own note on your blog, website, forums, blog comment, Facebook account or anywhere someone would find this page valuable.

Breaking Story – Diy Concrete Driveway Cost – The Real Cost Of Doing It Yourself!

The Latest News on Diy Concrete Driveway Cost – The Real Cost Of Doing It Yourself!

Original Source:
Category – Concrete

© 2022 - WordPress Theme by WPEnjoy